- 您现在的位置：买卖IC网 > Sheet目录537 > XT09-PKI-EA-NA (Digi International/Maxstream)MODEM RF 900MHZ 1W ETHER INT
9XTend ‐ PKG ‐ E? ? Ethernet ? RF ? Modem ? – ? Product ? Manual ? v2.x4x ? [2007.01.04]
DT (Destination Address) Command
<Networking & Security> DT Command is used to
set/read the networking address of an RF
modem. The modems utilize three filtration lay-
ers: Vendor ID Number (ATID), Channel (ATHP),
and Destination Address (ATDT). The DT com-
mand assigns an address to a modem that
enables it to communicate only with other
modems having the same address. All modems
that share the same DT parameter can communi-
cate with each other.
AT Command: ATDT
Binary Command: 0x00
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: HP (Hopping Channel), ID
(Modem VID), MK (Address Mask), MY (Source
Address)
RF modems in the same network with a different destination address (than that of the transmitter)
will listen to all transmissions to stay synchronized, but will not send any of the data out their
serial ports.
E0 (Echo Off) Command
<Command Mode Options> E0 Command turns
off character echo in AT Command Mode.
By default, echo is off.
E1 (Echo On) Command
<Command Mode Options> E1 Command enables
character echo in AT Command Mode. Each typed
character will be echoed back to the terminal
when ATE1 is active. E0 (Echo Off) is the default.
ER (Receive Error Count) Command
<Diagnostics> The ER command is used to set/
read the number of receive-errors. The error
count records the number of packets partially
received then aborted on a reception error. This
value returns to 0 after a reset and is not non-
volatile (Value does not persist in the modem's
memory after a power-up sequence). Once the
Receive Error Count reaches its maximum value
AT Command: ATE0
Binary Command: 0x0A (10 decimal)
AT Command: ATE1
Binary Command: 0x0B (11 decimal)
AT Command: ATER
Binary Command: 0x0F (15 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: GD (Receive Good Count)
(up to 0xFFFF), it remains at its maximum count
value until the maximum count value is explicitly changed or the modem is reset.
The ER parameter is not reset by pin, serial port or cyclic sleep modes.
FH (Force Wake-up Initializer) Command
<Sleep (Low Power)> The FH command is used
to force a Wake-up Initializer to be sent on the
next transmission. Use only with cyclic sleep
AT Command: ATFH
Binary Command: 0x0D (13 decimal)
modes active on remote modems.
ATFH will not send a long header if ATHT = 0xFFFF. WR (Write) Command does not need to be
issued with FH Command.
? ? 2007 ? MaxStream, ? Inc., ? Confidential ? & ? Proprietary ?‐? All ? Rights ? Reserved ?
????? 28
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
XT09-SI
MODULE RF 900MHZ 1W 115K W/RPSMA
XU-A11
X-STICK 2.4GHZ USB TO XBEE
XV-8000CB :3 50.3000KHZ+/-60DPS
AUTOMOTIVE GYRO SENSOR +/-60DPS
YB03WKW01-6B-JB
INDICATOR PB RECT WHT LED ILLUM
YGM1 C518
THERM PTC MINI-BEAD 3MM 180C
YQD120N0006
THERMISTOR PTC OCP 6 OHM 25C
Z4D-A01
PHOTO SENSOR 7.5MM REFLECT TYPE
ZALM-301-1C-B
RF TRANSCEIVER 100MW MMCX W/CONN
相关代理商/技术参数
XT09-PKI-E-NA
功能描述:射频模块 9XTend 1W Ethernet w/o accessories Intl
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R
功能描述:射频模块 9XTend 1W RS232/485 w/o accessories
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA
功能描述:射频模块 900MHz - Xtend software setable
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA-NA
功能描述:射频模块 9XTend 1W RS232/485 w/accessories no AES
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RDA
功能描述:射频模块 XTend-PKG 900 MHz IndRS-232class1/div2
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NA
功能描述:射频模块 9XTend 1W RS232/485 w/o accessories Intl
RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NL
制造商:Digi International Inc 功能描述:MODEM RF 900MHZ 9600/11
XT09-PKT-R
功能描述:MODEM RF 900MHZ RS232/485 RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:XTend™ 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125